## Can someone explain how tension and torque relates to bolted connections?

We’ll try our best. The relationship between tension and torque should be looked at cautiously, since it is very difficult to indicate the range of conditions expected to be experienced by a fastener. Torque is simply a measure of the twisting force required to spin the nut up along the threads of a bolt, whereas tension is the stretch or elongation of a bolt that provides the clamping force of a joint. Bolts are designed to stretch just a tiny bit, and this elongation is what clamps the joint together. Torque is a very indirect indication of tension, as many factors can affect this relationship, such as surface texture, rust, oil, debris, thread series and material type just to name a few. Virtually all the torque/tension tables that have been developed, including ours, are based on the following formula:

T = (K D P)/12

• T = Torque (ft-lbs)
• D = Nominal Diameter (inches)
• P = Desired Clamp Load Tension (lbs)
• K = Torque Coefficient (dimensionless)

The value of K is a dimensionless torque coefficient that encompasses variables such as those listed above, as well as the most significant variable, friction. The value of K can range from 0.10 for a well lubricated/waxed assembly, to over 0.30 for one that is dirty or rusty. The values we used when calculating our values are:

• 0.10 = Waxed/Lubricated
• 0.20 = Plain, as received condition, slightly oily
• 0.25 = Hot-Dip Galvanized

The appropriate torque value to use in a specific application is best obtained by using a calibrated torque wrench and a Skidmore-Wilhelm load indicating device to equate actual torque to the desired tension. For ASTM A325 and A490 structural bolts The Research Council on Structural Connections (RCSC) recommends:

The pre-installation verification procedures specified in Section 7 shall be performed daily for the calibration of the installation wrench. Torque values determined from tables or from equations that claim to relate torque to pretension without verification shall not be used.
RCSC Specifications, June 2004, pg. 62, 8.2.2

An alternative and more accurate method for assuring proper tension would be to use a direct tension indicator or DTI. These are available for use with ASTM A325 and A490 structural bolts and are engineered to compress at the proper tension, assuring the installer that the proper clamp load is achieved. Hopefully, this short introduction to bolt connections helps address some of the confusion surrounding this issue.

Written ,

Thank you so much was helpful

gerald says:

Great work, however a simple manufacturing method is fail 10 bolts and take the average and reduce by 10% of the failure point.

ROBERT RODRIGUES says:

hi i am robert
manufacturer high tensile bolts
also torquing and tensioning tools
whenever i go to on site for torquing i use tensioning tool so how calculate torquing value in tensioning tool

Dane McKinnon says:

@Robert- We are sorry, but we don’t have any experience using tensioning tools, so are unsure how to use them to calculate torque.

Bhola Sharma says:

can you send me socket head cap screw 50% torque chart

Dane McKinnon says:

@Bhola- Apologies, but we do not have any torque information on socket head cap screws.

R D Carmichael says:

carbon steel socket head cap screws torque the same as grade 8 bolts

Dane McKinnon says:

@RD- Torque requirements will vary by application type, so we can’t make any specific recommendations. Additionally, socket head screws usually thread into tapped holes, whereas grade 8 bolts may be used with a nut, so it isn’t an apples to apples comparison.

Jugal says:

Dan,

We have tested few Grade 8 Bolts & nuts Plain with slightly oil finish of 1.1/2-6 .
And results are torque is approx. 3146 Nm – 3164 Nm, Pretension force is approx. 455 kN – 497 kN & Torque co-efficient is approx. 0.166-0.183.

So, let me know your feedback.

Dane McKinnon says:

@Jugal- We are not surprise that your values vary a bit from ours. Torque is a tricky and unpredictable measure of tension and can vary from bolt to bolt depending on the conditions.

Asmita says:

Hi, I used 5/8″ bolt with ASTM A36 material and calculated Torque value by above formula. Through calculations I got 70 N-m torque value but in actual practise when I measured, it came around 30 N-m until there was a bent in Bolt clamp bar. I used Friction factor of 0.15 and calculated. Not able to understand why am I getting this huge difference.

Dane McKinnon says:

@Asmita- Torque is a tricky subject, and there are many variables that can come into play. Variations are common, although yours seems excessive. Without having all the information, we are unable to help, but I would start by double checking your values to make sure an error was not made. That said, 70N-m seems quite high for 5/8″ A36, I would have expected 60 N-m or lower with a K factor of 0.15.

Steve Lee says:

dane,
Just curious about something I learned – one design called for 1 1/2″ Gr 8 bolt with 2200 ft-lb tightening torque. now the engineer claimed that by specifying a 1000 ft-lb tightening torque will be adequate based his calculation. my comment to him was that then don’t use 1 1/2″ size bolt and go to a 7/8″ or whatever, so that I can save some money. the other aspect of the bolt property for 1 1/2″ size, in order for this bolt to be effective was that ~ 2200 ft-lb is to apply. please advise and thank you in advance.

Dane McKinnon says:

@Steve- Torque is a crude method of measuring tension, so more information would be required before a determination could be made. I would discuss more in depth with your engineer to see what alternatives might be possible.

Dan says:

What’s amusing is that this equation doesn’t even slightly resemble the ideal model of the simple circular wedge machine that a bolt actually is. It turns out that this is because friction dominates the demand for input torque. Even though it is the thread pitch term (which cannot be seen here) that actually physically generates the tension, it becomes almost irrelevant in calculating it!

Yvon Lavoie says:

I have a question,

Someone told me that if I use an helical spring in a particular connection, I shoul decrease the torque applied to the bolt by maybe one half?

I am not a specialist, but I think that it is not right! We should use the same torque??

Am I right?

Thank you very much.

Y. Lavoie

Dane McKinnon says:

@Yvon – I believe you are correct, the torque would not need to be decreased because of the lockwasher.

Marcus Ibe says:

Specifying bolts sizes and torque value requires you first, analyse the force interaction at the joint you’re connecting, then calculate the tensile stress area based on 75% of your selected material proof strength. Then specify a bolt size. These days, people just specify over and above what is required without any engineering!

Godfred says:

how do i calculate Torque for a bolt,when there is a 257 KN pre-tension minimum for a 10.9grade M24bolt

Dane McKinnon says:

@Godfred – Apologies, but we do not have any torque information for metric or grade 10.9 fasteners.

Dan M says:

This question is a bit off the beaten path. I am reinstalling a handhole cover on a tank. The drawing gives a torque spec of 27 +/-3 ft/lbs. Original gasket was Grade 1 (65 durometer) rubber. Only gasket material I can get is Grade 2 at (80 durometer). Does the increased hardness of the gasket material affect my torque value?

@Dan – I’m sorry, but we don’t have the expertise to answer this. Apologies.

Jeremy says:

Due to stocking of hardware and varying applications, we use a majority of ASTM A574 Screws. If we are torquing ASTM A574 Screws to a Grade 5 torque(due to lesser application requirements), is it feasible that we are more likely to have screws working loose? My thought is that we are not putting enough tension into the higher strength screw.

@Jeremy – It would all depend on the application. Static loads may be OK, but if there is movement or vibration, you may have an issue. We don’t have any engineers on staff, so we can’t really make a determination. Apologies.

Dan says:

Hi,

I am looking for bolts that have rounded/dome ends. Do you know where I could find some? Specifically, I need 1/4-20 stainless steel bolts with rounded ends. I don’t even know if there is a special name for such, but the closest I’ve come to finding them is this website, and I searched for “round end bolt”

Thanks!

@Dan – I am sorry, but I am not sure where you could find bolts like that, other than having them specially made. Apologies.

Steve says:

Would the coefficient for a lubricated hot dip galvanized bolt be 0.1?

@Steve – We use 0.10 in our torque calculations, but I have read anywhere from 0.10 to 0.15 is realistic. It will likely vary in that range from manufacturer to manufacturer.

mel says:

Can you explain to me what will happen if we apply more torque on the installed bolt? Example, the required torque is only 200 ft-lb… then we apply 250 ft- lb…. what will be the effect of this on the structure and on the bolt itself?

@Mel – Without more information I cannot be certain, but the possibilities include snapping the bolt, crushing whatever you are bolting, or maybe nothing. It will depend on the capacity of the bolt in question, what you are bolting, and the amount of friction in the bolted assembly.

ersin says:

I used M10 10.9 allen head screw on the aluminium rail. for assembly of bus seats..under rail there is sheet. ı searched a lot. everybody is saying aluminium reduce the torque value.
ı found 33.9 Nm and 20Nm. difference is too big.

@Ersin – Thank you for your question, but our area of expertise is with carbon and alloy steel structural applications, we don’t have any information regarding aluminum Apologies.

Jared says:

Is there a torque chart for different sizes of the ASTM 1554 grade 36 anchor rods?

@Jared – These torque charts are calculated for use in steel to steel connections. Anchor bolts are not typically torqued to a specific requirement, as the AISC says that snug tight is acceptable.

Duncan says:

Any guidance for 3/4″ lag bolts in SYP timber? Specifically a railing base plate with lags into stringer below (perpendicular to grain), with concerns about torque loading that twists off the lag and how much to reduce this torque to avoid lag damage? Do you have maximum allowable torques for lags?

@Duncan – Apologies, but we do not have any engineers on staff, so cannot comment on application-specific questions like this. I am not aware of any allowable torque values for lag bolts.

Alex says:

P = Desired Clamp Load Tension (lbs), is this the value given in kips on the RCSC code, if so how to convert to lbs

Jegan says:

Hi, I need the Torque report format, Could you provide format(sample)? Until we dont have the format.Thanks

@Jegan- I am unsure what you are requesting. You can download the torque chart as a pdf, or you can print what you see on the screen.

Lily Well says:

For 5/8″ Step bolts, of SAE grade 2, what torque value should we be specifying during installation. This is for a transmission line tower.

@Lily – That is a difficult question to answer. We have torque values on our website, but every application is a bit different, so there is no one all encompassing torque value that works for all applications. Controlled lab testing is the only sure fire way of determining your specific torque values. /technical/bolt-torque-chart/

Manoj V K says:

@Dane McKinnon -Thanks

Manoj V K says:

The same above mentioned formulae are used for calculating torque for countersunk screws or any other multiplication factor available…???

@Manoj – The torque formula would differ from the one listed because screwing into tapped holes usually creates a longer thread engagement which can affect the friction coefficient. An engineer would be the best person to consult regarding this.

Charles says:

Hevii Guy,

There is no such thing as an overtightened connection, until you break the bolt in tension. RCSC – Sec. 9.2.4, states: “A pretension that is greater than that specified in Table 8.1 shall not be cause for rejection”

Mike Girard says:

Just a minor point of clarification: Torque is not energy. It is a twisting force.

Jonathan Waltner says:

@Mike Girard – You are absolutely right. The content of the post has been updated. Thanks for catching that.

Hevii Guy says:

Direct Tension Indicationg washers provide a false sense of security: They cannot indicate whether the joint has been overtightended. Neither do they provide a means of checking load migration after initial installation.
Skidmore-Wilhelm machines provide an accurate indication of torque to load but ONLY on the exact fastener being measured under the the conditions experienced in the device AT THAT TIME. Once the tested wrench is used in the field, myriad friction factors and load interactions mean that all bets are off; one has no way of knowing what the actual load will be – it’s still a “guessing” exercise unless load is verified AFTER the bolt has been tightened and then again, after all of the other bolts have been tightned (to compensate for load transfer)

Galliou » It is hard to say if these calculations would be very accurate for anchor bolts. The biggest uncontrolled variable when determining torque is friction. Since the surface between the bolt assembly and the joint surface in the field can vary greatly it is difficult, if not impossible to accurately estimate torque for anchor bolts. One option would be to consider load indicating washers. This washer will give consistent tension values regardless of environment.

Galliou says:

Is the “Bolt Torque Chart” applicable for anchor bolts?